113 – Anti UV One Way Mirror Film Daytime Privacy

Very good product. I only wish if they can send holders or something to hold film while installing .it’s bit tough with bare hand to hold on edges whiles finishing install

These were not that hard to install, if you follow instructions and take your time they can look very good. My pictures show during daytime you cannot see inside, and you can see outside with minimal visual distortion. I did not take night pictures, but at night you can see inside. The only downside to these is that looking from inside to the outside at night seemed very poor.

This is what I found to work best for install.

If you have plenty of material left over after cutting out what you need, use some of the excess to practice with.

1. Get a good squeegee – I got this one EHDIS Small Squeegee 5 inch Rubber Window Tint Squeegee for Car, Glass, Mirror, Shower, Auto,Windows
2. Thoroughly clean your windows. Don’t just wipe them down, clean them. Clean them a few times.
3. Measure the glass you want to cover, then add at least a half inch to each edge. So if your window is 20″ wide, you want at least 21″ of material or more.
4. Cut your material to the amount you just figured out.
5. Make a spray bottle of soapy water. Don’t go crazy with the soap, just a drop or two is plenty.
6. Spray your window so that every inch is wet and the water is dripping down – you cannot get it too wet.
7. Peel the plastic protective sheet off the film.
8. Spray the cling side of the film (the same side that had the protective plastic) with your soapy water.
9. Give another couple sprays to the window, especially the top edge if your water has dripped down.
10. Place the film onto the window so that the edges overlap the window. The film will automatically cling to the window and some of the soapy water will go away. You can adjust the position of the film as necessary to get the edges overlapping.
11. Use the squeegee ONLY in a small section of the center of the window – DO NOT wipe to the edges. This will help the film stay in place while you cut it to fit. You do not want to squeegee to the edges because you still need the soapy water to help the edges stick after you get the film trimmed to size.
12. Use a sharp hobby/exacto knife to cut the film. Push the film down so that it gets as far into the corner of the glass and the frame as possible. I found it easier to start from the middle and work my way into the corners. Go VERY SLOW! A nice slow cut will help you cut straight. I also found it helpfull to cut an entire sliver off, and not just to the corner of the window.
13. Once you have it completely trimmed, use the squeegee starting from the center of the window and work your way to the outside edges. Do it multiple times, even if it looks like the soapy water is gone.
14. If you have any edges that are not sticking, gently pull the edge back far enough that you can spray more soapy water in there, then use the squeegee again.

KESPEN Window Privacy Film was the solution I was looking for to make my home and office more tranquil and secure. This sun-blocking, anti-UV, and reflective one-way daytime privacy solution seemed like a good option. There are several things to keep in mind despite its many strengths. In this comprehensive 4-star review, I’ll talk about my experience with the KESPEN Window Privacy Film, including its features, performance, and overall value.

The KESPEN Window Privacy Film distinguishes out because it does more than just provide privacy; it also blocks the sun. The midday isolation is much appreciated thanks to the one-way privacy element that blocks views from the outside. The sun-blocking and anti-UV characteristics simultaneously lessen glare and shield furniture from overexposure to the sun.

The static cling design made the assembly process quick and easy. However, some patience and accuracy were required to complete the application without any bubbles. The film’s generous dimensions of 17.5 inches by 6.5 feet made it usable for a wide range of window sizes.

The film’s one-way privacy effect works best during the day, which is an important consideration. The privacy feature loses its effectiveness when inside lighting is brighter than the outdoor surroundings, as is the case in the evening. Expectations must be managed, and extra window coverings should be considered for nocturnal privacy.

The KESPEN Window Privacy Film did a great job of keeping the inside of my house private throughout the day. It let me see out yet blocked prying eyes from the inside, giving me the much-needed privacy I was seeking. The mirrorlike appearance provided by the reflective surface amplified this illusion further. This made my windows look more contemporary.

While the film’s reflective quality is great for privacy, it’s important to keep in mind that it can also make it difficult to see out the window during the day. This effect may be more noticeable in rooms with a lot of natural light, which may reduce the level of comfort there.

The film’s ability to hide the sun was immediately noticeable. I was able to use my computer and watch TV without getting eye strain because of the significant decrease in strong glare. The film’s anti-UV capabilities added peace of mind, since I knew it was shielding my things from the sun’s harmful rays.

It’s important to remember, though, that the sun-blocking effect can also drastically reduce the amount of light entering the room. This could be problematic in areas where natural light is particularly important, yet ideal, such as theater rooms. It’s crucial to weigh the advantages of sunshading against the reduction in indoor lighting.

As was noted earlier, the installation process was simple, however there were some difficulties in establishing a bubble-free application. Static cling technology makes adjustments easy during set up. However, it might be tricky to align exactly due to the film’s reflecting surface, as it can be difficult to see through the film from the inside.

Throughout my experiments, the film kept its initial adherence and performance levels. There was no peeling or deterioration, so you know it was well made.

If you’re looking for a practical way to protect your privacy and shield yourself from the sun, consider the KESPEN Window Privacy Film. Its low price makes it a desirable alternative to more permanent window coverings like blinds. It is important to weigh the benefits against any potential downsides, such as increased interior reflection and less natural light.

If you’re looking to improve privacy and cut down on glare without breaking the bank, look no further than the KESPEN Window Privacy Film. Because of its double purpose, static cling construction, and shielding qualities, it can be used in a variety of settings. The film’s overall performance and low cost score it a solid 4 stars, despite minor concerns regarding nighttime privacy, inside reflectivity, and impact on interior illumination. KESPEN Window Privacy Film may do wonders for your comfort and privacy provided it is installed properly and its features are taken into consideration.

I love it and would buy it again. It does its job well. Keeping mind, it only works during the day, as long as there is more light outside.

Installing should be ready, but I’ve made quite a few mistakes. Here’s my lessons learned. Be gentle with it. If you try to push out the bubbles too hard it will crack the film. If you place it once and there are too many bubbles try it again that should be no bubbles in the middle. The way I accomplished that, on my gazillion try, is by installing from the middle out. Also, the squeegee did not do much for me. I I covered a spatula with a soft fabric and use it to push the bubbles out from the middle to the outside, very gently after I had damaged it the film by pushing too hard. If you start from the middle it will not be hard and it should not. If it becomes too hard, pull it out and start again